category: Manufacturing, Packaging and Materials

category: IoT, Security & Automotive

Manufacturing Bits: Dec. 13
By Mark LaPedus - 13 Dec, 2016 - Comments: 0

Phonon lasers A European consortium recently kicked off a new project that will develop a practical phonon laser. The European consortium, called PHENOMEN, will be coordinated by the Catalan Institute of Nanoscience and Nanotechnology (ICN2). Most chips perform functions using an electrical charge (electrons) or by light (photons). In comparison, a phonon “is a quantum of energy or a q... » read more

The Week In Review: Manufacturing
By Mark LaPedus - 09 Dec, 2016 - Comments: 2

Chipmakers At this week’s IEEE International Electron Devices Meeting (IEDM) in San Francisco, TSMC as well as the team of GlobalFoundries, IBM and Samsung separately presented papers on 7nm finFET technology. Qualcomm has begun sampling the world’s first 10nm server processor. As the first in the Qualcomm Centriq product family, the ARM-based processor has up to 48-cores and is built ... » read more

Manufacturing Bits: Dec. 6
By Mark LaPedus - 06 Dec, 2016 - Comments: 1

The National High Magnetic Field Laboratory (MagLab) has broken an unofficial record for the world’s most powerful hybrid magnet. The 33-ton system, called the series connected hybrid (SCH) magnet, has reached its full field strength of 36 tesla. The SCH is more than 40% stronger than the previous world-record hybrid magnet. Tesla, or T, is the measurement of magnetic field strength. A ref... » read more

The Week In Review: Manufacturing
By Mark LaPedus - 02 Dec, 2016 - Comments: 0

Manufacturing There are more changes at SEMI. SEMI has named David Anderson as president of the SEMI Americas region. Most recently, Anderson was chief executive and chairman of Novati, a specialty manufacturing fab. He replaces Karen Savala, who was president of the SEMI Americas region for six years. In an e-mail, Savala confirmed she left SEMI in October. Meanwhile, in October, SEMI an... » read more

Sustainability Saves Water, Too
By Katherine Derbyshire - 30 Nov, 2016 - Comments: 0

After energy (discussed in Part 2 of this series), water is the largest fab input and the largest contributor to fab waste. Yet tools for analyzing a fab’s water footprint are generally less mature than tools for analyzing emissions of CO2 and other greenhouse gases. In part, this may be because water consumption is primarily a local issue, while greenhouse gas emissions are a global c... » read more

Manufacturing Bits: Nov. 29
By Mark LaPedus - 29 Nov, 2016 - Comments: 0

Supersonic kinetic spraying Low-cost flexible electronics could enable a new class of products, such as roll-up displays, wearable electronics, flexible solar cells and electronic skin. There is a major barrier to enable these technologies, however. The problem is to make flexible transparent conducting films that are scalable and economical. The University of Illinois at Chicago and Kor... » read more

Multi-Patterning Issues At 7nm, 5nm
By Ed Sperling - 28 Nov, 2016 - Comments: 13

Continuing to rely on 193nm immersion lithography with multiple patterning is becoming much more difficult at 7nm and 5nm. With the help of various resolution enhancement techniques, optical lithography using a deep ultraviolet excimer laser has been the workhorse patterning technology in the fab since the early 1980s. It is so closely tied with the continuation of [getkc id="74" comment="Mo... » read more

The Week In Review: Manufacturing
By Mark LaPedus - 25 Nov, 2016 - Comments: 0

R&D Amid budget cuts in the U.S. government, federal funding for R&D at higher education institutions in the United States declined for a fourth straight year, according to a new report from the National Center for Science and Engineering Statistics (NCSES). Overall, universities reported $68.8 billion in R&D expenditures in 2015, a 2.2% increase from 2014, according to the NCSES, part of t... » read more

Manufacturing Bits: Nov. 23
By Mark LaPedus - 23 Nov, 2016 - Comments: 1

Materials database The Department of Energy’s Lawrence Berkeley National Laboratory has published a study that quantifies the thermodynamic scale of metastability of some 29,902 materials. To quantify the materials, researchers used Berkeley Lab’s Materials Project, a large and open database of known and predicted materials. The open and Web-based database has calculated the properties ... » read more

Can We Measure Next-Gen FinFETs?
By Mark LaPedus - 21 Nov, 2016 - Comments: 6

After ramping up their respective 16nm/14nm finFET processes, chipmakers are moving towards 10nm and/or 7nm, with 5nm in R&D. But as they move down the process roadmap, they will face a new set of fab challenges. In addition to lithography and interconnects, there is metrology. Metrology, the science of measurements, is used to characterize tiny films and structures. It helps to boost yi... » read more

← Older posts Newer posts →

  • Sponsors

About

Navigation

Connect With Us

Copyright ©2013-2025 SMG   |  Terms of Service  |  Privacy Policy