The Week In Review: Manufacturing And Design

By Mark LaPedus - 10 Jan, 2014 - Comments: 1

Crucial.com reveals a surprising way to gain more time for improving one's personal health: fix a slow computer. A nationwide survey revealed that U.S. adults think they waste an average of 16 minutes per day waiting for their computer to load or boot up. Equating to two hours each week and four days per year lost to the wiles of a slow computer, it's no surprise that 66% of Americans say that ... » read more

The Week In Review: Manufacturing & Design

By Mark LaPedus - 13 Dec, 2013 - Comments: 0

Tensions between the U.S. and China are growing. In a research report, Gus Richard, an analyst at Piper Jaffray, said: “The technology sector is being impacted by U.S./Chinese tensions over cybersecurity. The combination of Huawei being blocked from doing business in the United States and the Snowden affair are impacting U.S. tech companies' prospects in China. China’s state-run media ident... » read more

2014 CapEx: Memory Is Leading The Way

By Adrienne Downey - 12 Dec, 2013 - Comments: 0

The semiconductor industry is expensive. Billions of dollars are spent every year to keep the fabs running, build new fabs, and push the process technology to greater and greater heights. Billions more will be spent to make 450mm production a reality. In January 2013, Semico predicted that, based on initial indications from some companies, total CapEx would be flat this year. Based on current d... » read more

Challenges Mount In Inspection And Metrology

By Mark LaPedus - 12 Dec, 2013 - Comments: 0

Chipmakers are moving full speed ahead toward smaller process nodes, thereby driving up the costs and complexities in chip manufacturing. The migrations also are putting enormous stress on nearly all points of the fab flow, including a critical but unsung part of the business—process control. Process control involves 20 or so different segments in the inspection and metrology arena. Genera... » read more

Semiconductor New Equipment Market $32.0 Billion For 2013

By Lara Chamness - 12 Dec, 2013 - Comments: 0

Orders for new equipment slowly improved early on in 2013, with bookings reaching a peak by the second quarter before receding in the third quarter. Over this time, equipment billings, while increasing, were trending below 2012 levels. In October, book-to-bill data from both SEMI and the SEAJ show bookings are increasing once again, and this indicates a stronger fourth quarter for the semico... » read more

Momentum Builds For Monolithic 3D ICs

By Mark LaPedus - 14 Nov, 2013 - Comments: 1

The 2.5D/3D chip market is heating up on several fronts. On one front, stacked-die using through-silicon vias (TSVs) is taking root. In a separate area, Samsung is sampling the world’s first 3D NAND device, with Micron and SK Hynix expected to follow suit. And now, there is another technology generating steam—monolithic 3D integrated circuits. In stacked-die, bare die are connected using... » read more

What’s After 3D NAND?

By Mark LaPedus - 19 Sep, 2013 - Comments: 0

By Mark LaPedus Planar NAND flash memory is on its last scaling legs, with 3D NAND set to become the successor to the ubiquitous 2D technology. Samsung Electronics, for one, already has begun shipping the industry’s first 3D NAND device, a 24-level, 128-gigabit chip. In addition, Micron and SK Hynix shortly will ship their respective 3D NAND devices. But the Toshiba-SanDisk duo are the lo... » read more

MRAM Begins To Attract Attention

By Mark LaPedus - 19 Sep, 2013 - Comments: 0

By Mark LaPedus In the 1980s, there were two separate innovations that changed the landscape in a pair of related fields—nonvolatile memory and storage. In one effort, Toshiba invented the flash memory, thereby leading to NAND and NOR devices. On another front, physicists discovered the giant magnetoresistance (GMR) effect, a technology that forms the basis of hard disk drives, magnetores... » read more

450mm: Out Of Sync

By Mark LaPedus - 18 Jul, 2013 - Comments: 0

By Mark LaPedus The IC industry has been talking about it for ages, but vendors are finally coming to terms with a monumental shift in the business. The vast changes involve a pending and critical juncture, where the 450mm wafer size transition, new device architectures and other technologies will likely converge at or near the same time. In one possible scenario, 450mm fabs are projected ... » read more

New Approaches To Better Performance And Lower Power

By Ed Sperling - 11 Jul, 2013 - Comments: 0

By Ed Sperling Until 90nm, every feature shrink and rev of Moore’s Law included a side benefit of better power and performance. After that, improvements involved everything from different back-end processes to copper interconnects and transistor structures. But from 20nm onward, the future will rest with a combination of new materials, new architectures and new packaging approaches—and som... » read more

← Older posts Newer posts →

Knowledge Centers
Entities, people and technologies explored

Shift Left Is The Tip Of The Iceberg

A transformative change is underway for semiconductor design and EDA. New languages, models, and abstractions will need to be created.

by Brian Bailey

Partitioning In The Chiplet Era

Understanding how chiplets interact under different workloads is critical to ensuring signal integrity and optimal performance in heterogeneous designs.

by Ann Mutschler

3.5D: The Great Compromise

Pros and cons of a middle-ground chiplet assembly that combines 2.5D and 3D-IC.

by Ed Sperling

AI’s Role In Chip Design Widens, Drawing In New Startups

Focus is on letting engineers do much more with the same or fewer resources — and less drudgery.

by Karen Heyman

What Comes After HBM For Chiplets

The standard for high-bandwidth memory limits design freedom at many levels, but that is required for interoperability. What freedoms can be taken from other functions to make chiplets possible?

by Brian Bailey

Memory Fundamentals For Engineers

eBook: Nearly everything you need to know about memory, including detailed explanations of the different types of memory; how and where these are used today; what's changing, which memories are successful and which ones might be in the future; and the limitations of each memory type.

by The SE Staff

Why Small Fab And Assembly Houses Are Thriving

Megafabs churning out the most advanced processors are not the only game in town.

by Bryon Moyer

New AI Processors Architectures Balance Speed With Efficiency

Hot Chips 24: Large language models ratchet up pressure for sustainable computing and heterogeneous integration; data management becomes key differentiator.