category: Manufacturing, Packaging and Materials

category: Auto, Security & Edge AI

The Week In Review: Manufacturing
By Ed Sperling - 01 Jun, 2018 - Comments: 0

Cleanliness is a good thing. In the fab, it's also a very profitable thing. According to a report from Research and Markets, the wafer cleaning systems market will grow more than 6%. The research house notes, however, that the rate of growth is slowing. GlobalFoundries began volume production of its 180nm ultra-high-voltage process for industrial and power applications. The base platform sta... » read more

What’s In A Node?
By Sundeep Bajikar - 30 May, 2018 - Comments: 0

In an environment where process nodes are no longer consistently delivering the level of improvements predicted by Moore’s Law, the industry will continue to develop “inter-nodes” as a way to deliver incremental improvements in lieu of “full-nodes.” A shift in market requirements, in part due to the rise of AI and IoT, is increasing emphasis on trailing-nodes. When it comes to leading... » read more

Transistor-Level Performance Evaluation Based On Wafer-Level Process Modeling
By Michael Hargrove - 30 May, 2018 - Comments: 0

Three years ago, I wrote a blog entitled “Linking Virtual Wafer Fabrication Modeling with Device-level TCAD Simulation,” in which I described the seamless connection between the SEMulator3D virtual wafer fabrication software platform and external third-party TCAD software. I’m now happy to report that device-level I-V performance analysis is now a built-in module within the SEMulator3D so... » read more

Understanding The Effect Of Variability In Bulk FinFET Device Performance
By Coventor - 30 May, 2018 - Comments: 0

2-D MOSFETs have proven difficult to scale down to 20nm and beyond. In their place, 3D FinFET transistors have emerged as novel devices that can scale down to lower node sizes. 10nm process finFETs are for SoC product mass production, and research is progressing towards a 7nm process finFET. FinFET transistors provide lower dynamic power consumption (due to flatter I-V curves), improved control... » read more

Manufacturing Bits: May 29
By Ed Sperling - 29 May, 2018 - Comments: 0

Utilizing Heat For Energy One of the big problems in electronics in general, and semiconductors particular, is heat. And it's not just about leakage current anymore. Heat is a problem at every level, from circuit design to the materials being used inside the chips, as well as warpage between die caused by heat after they are packaged together. Heat can prematurely age chips as well as destroy ... » read more

The Week In Review: Manufacturing
By Mark LaPedus - 25 May, 2018 - Comments: 0

Chipmakers GlobalFoundries has announced that its 22nm FD-SOI technology platform has been certified to AEC-Q100 Grade 2 for production. As a part of the AEC-Q100 certification, devices must withstand reliability stress tests for an extended period of time and over a wide temperature range in order to achieve Grade 2 certification. Presto Engineering has joined GlobalFoundries’ ecosystem ... » read more

Quantum Effects At 7/5nm And Beyond
By Ed Sperling - 23 May, 2018 - Comments: 5

Quantum effects are becoming more pronounced at the most advanced nodes, causing unusual and sometimes unexpected changes in how electronic devices and signals behave. Quantum effects typically occur well behind the curtain for most of the chip industry, baked into a set of design rules developed from foundry data that most companies never see. This explains why foundries and manufacturing e... » read more

Manufacturing Bits: May 22
By Mark LaPedus - 22 May, 2018 - Comments: 0

Exotic water The Deutsches Elektronen-Synchrotron (DESY) organization, Uppsala University and SLAC have turned a large X-ray laser into the world’s fastest water heater. Using an X-ray free-electron laser from the SLAC National Accelerator Laboratory, researchers have heated water from room temperature to 100,000 degrees Celsius in less than a tenth of a picosecond or a millionth of a mil... » read more

200mm Fab Crunch
By Mark LaPedus - 21 May, 2018 - Comments: 2

Growing demand for analog, MEMS and RF chips continues to cause acute shortages for both 200mm fab capacity and equipment, and it shows no sign of letting up. Today, 200mm fab capacity is tight with a similar situation projected for the second half of 2018 and perhaps well into 2019. In fact, 2018 will likely represent the third consecutive year that 200mm fab capacity will be tight. The sam... » read more

The Week In Review: Manufacturing
By Mark LaPedus - 18 May, 2018 - Comments: 1

Fab tools and test VLSI Research released its annual "Customer Satisfaction Survey" and listed "THE BEST Suppliers" of 2018. VLSI Research received feedback from more than 94% of the chip market and 76% of subsystems customers for this year’s survey. Who are the winners? Applied Materials reported its second quarter results, along with its business outlook. Compared to the second quarter ... » read more

← Older posts Newer posts →

  • Sponsors

  • Standards/Organizations

About

Navigation

Connect With Us

Copyright ©2013-2026 SMG   |  Terms of Service  |  Privacy Policy